How To Repair A Pool Stick

Posted past : .(JavaScript must be enabled to view this email address)

Replacing a Pool Cue Tip: 6 Easy Steps to practice information technology Yourself

It'due south similar a bad dream. Your tip is worn out, you accept a tournament coming upwards and you tin can't get to your local cue repair guy, or maybe there isn't a cue repair guy in your area at all! Well today is your lucky day! Today we are going to learn how to install a new tip on your cue using the Tweeten Cue Tip Repair Kit . This is something every pool player should know. Allow'south become started.

The moving-picture show below shows our poor, worn out tip. This tip is pretty low and in danger of existence both detrimental to your game and perhaps even damaging your ferrule.

This is what a worn out pool cue tip looks like. If your tip looks like this (or worse), and so it's time to supercede it!

Step one: Remove the Old Pool Cue Tip

The first pace is to remove the old tip. To practise this, you will need a overnice sharp razor blade (please be careful folks, information technology's hard to explain how you lot cutting off your finger changing your cue tip). Try and go equally close to the ferrule as you can. This may take a few passes with the razor blade. Just have your time and slowly remove whatsoever leather and excess glue as seen in the sequence below.

Exist extra careful removing your old tip then yous don't gash the side of the ferrule or your fingers.

Step 2: Make clean the Pool Cue Ferrule

One time you are satisfied with your job removing the sometime tip you demand to make sure the elevation of the ferrule is clean and equally flat as possible. To do this you will now use the rapid top sander included in the repair kit. Just place the shaft against the guide as shown in the following pictures and rotate until whatever leftover dirt and glue are removed from the top of the ferrule. Be certain to go on the sander prissy and level.

A clean, flat ferrule surface is crucial for the glue to hold properly. The rapid top sander in the Tweeten Repair Kit performs this stride perfectly.

Step three: Prepare the Pool Cue Tip

Preparing the tip is the next footstep in the process. To do this, take your favorite tip and use a piece of sandpaper to rough up the mucilage side of the leather. I do this by laying the sand paper on a flat surface to make sure as I sand the back of the tip I continue information technology perfectly flat and level. Sand the tip until it is nice and rough. It is important to make sure the tip is roughed up so the glue has something to adhere to. Apply the supplied tip cement or your favorite adhesive (I also recommend any type of gel super gum) to the tip.

Roughing up the lesser of your new pool cue tip is a adept way of making sure the glue has somewhere to grab. Make sure to put some glue on the ferrule side, too!

Stride 4: Identify the Puddle Cue Tip on the Ferrule

In the following sequence, you will come across the next step is to place the tip on the ferrule. Brand sure to go the tip centered every bit best you tin. Press firmly on the tip to make sure any air pockets are removed; the glue will push button out onto the ferrule. While property the tip in place, use some paper towel to wipe the glue that has now no dubiousness gotten on the ferrule. The more we can get off the ferrule now the less yous have to worry about trying to sand off later. Adjacent, assemble the tip clench that came with your kit. This clench slips over the shaft and equally you can see in the photo, you lot merely place the rubber band on the center of the tip and pull the clench down. Employ the slider to hold the clamp in identify. Permit the gum dry out for x to fifteen minutes.

Center the tip, printing downwards, and wipe off the backlog glue. Then use the tip clamp to keep pressure while the glue sets for fifteen minutes or longer.

Stride five: Cut and Sand the Cue Tip to the Ferrule

The side by side footstep is the part that requires a little patience and some practice—cutting the tip to match the bore of your ferrule. I like to place the shaft on a hard surface with the tip downwards as shown below. Use your razor bract to slowly shave away the sides of the tip. Don't try to take off too much leather at once, it is easier to move slowly. When you go closer y'all tin can utilise your ferrule as a guide. Make sure yous cut down towards the table in as straight a line as you can. On a side note, don't do this on your kitchen/dining room table….wives and or mothers exercise not appreciate pocket-sized razor cuts in the finish. Don't ask me how I know this. In one case you accept the tip the same diameter as the ferrule, you can clean it up some more than and remove any flat spots from the razor blade using a piece of 800 grit sand paper. Be careful not to sand too much on your ferrule.

Again, be extremely cautious with this step so you can avoid damaging your pool cue ferrule. Utilize a high dust sandpaper to get that terminal piece of the tip perfect.

Stride 6: Shape the Puddle Cue Tip

So now you lot have a tip glued firmly on and the same diameter as your ferrule, but it is probably flat. Time to shape information technology up. Use your favorite tip shaper, or the shaper that comes in the kit. Sand the tip until yous get the desired shape y'all prefer, dime, nickel etc. Once y'all take the tip shaped upwards, moisten the side of the tip (a niggling water works fine, merely don't get it too wet). Use a nice piece of leather to burnish the sides of your tip, below shows the Pooldawg Tip and Shaft Burnisher .

Burnishing the side of the tip gives it a shine finish and helps it to hold its shape.

Nosotros now have our finished tip. Not everyone has access to a good cue repair person or even the use of a lathe to install tips, just there is no reason to worry at present that you know how to put your ain tips on. Your first attempts might exist a petty rough, only in time you will develop your ain methods and your tip installs will improve.

Here is the final production. Attempt it yourself and you'll see that it's easier than you lot think to change your own puddle cue tip.

Until next time.

Mikey V.

• RELATED Manufactures
• How to Change a Pool Cue Tip – By Florian "Venom" Kohler
• Shaping your Pool Cue Tip – By PoolDawg Staff
• How to Cull the Right Pool Cue Tip – By Mikey Verkruyse

Source: https://www.pooldawg.com/article/pooldawg-library/replacing-a-pool-cue-tip

Posted by: ouelletteglikeels.blogspot.com

Share this post